{"product_id":"tin-roof-starlink-mount-roof-kit-for-dishy-gen-3-v4","title":"Tin\/Metal Roof Mount Kit for Starlink Standard (Gen 3 \/ V4) – Heavy Duty","description":"\u003cp\u003e\u003cem\u003e✅ Compatibility note: This product suits the \u003cstrong\u003eStarlink Standard (Gen 3 \/ V4)\u003c\/strong\u003e flat rectangular terminal, also commonly called \u003cstrong\u003eStandard Kit, Standard 4 or V4\u003c\/strong\u003e. It does \u003cstrong\u003enot\u003c\/strong\u003e suit Starlink Mini, Gen 2 actuated Standard, High Performance or Flat High Performance models unless specifically stated.\u003c\/em\u003e\u003c\/p\u003e\u003ch2 data-end=\"274\" data-start=\"198\"\u003e\u003cstrong data-end=\"274\" data-start=\"200\"\u003eStarlink Standard (Gen 3 \/ V4) Tin Roof Mount Kit with Heavy Duty 40mm Pole Adapter\u003c\/strong\u003e\u003c\/h2\u003e\n\u003cp data-end=\"687\" data-start=\"296\"\u003eThe Spacetek Heavy Duty Tin Roof Mount Kit is designed for permanent installation of the Starlink Standard (Gen 3 \/ V4) rectangular terminal on corrugated metal roofing in \u003cstrong data-end=\"500\" data-start=\"457\"\u003ehigh wind load and exposed environments\u003c\/strong\u003e. The system uses a reinforced mounting assembly combined with a heavy-duty machined aluminium \u003cstrong data-end=\"607\" data-start=\"576\"\u003eGen 3 to 40mm pole adapter\u003c\/strong\u003e, delivering increased rigidity and improved resistance to uplift and vibration.\u003cbr\u003e\u003cmeta charset=\"utf-8\"\u003e\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003eKit Inclusions: \u003c\/strong\u003e\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 x Standard (Gen 3 \/ V4) Heavy Duty Aluminium Pole Adaptor Kit, suits UTA-232.\u003c\/li\u003e\n\u003cli\u003e2 x Structural Telescopic Stay Bars (Galvanised Steel)\u003c\/li\u003e\n\u003cli\u003e1 x Aluminium Base Plate \u003cmeta charset=\"utf-8\"\u003e(270mm x 75mm)\u003c\/li\u003e\n\u003cli\u003e1 x Aluminium Pole Mast (choice of length) \u003cmeta charset=\"utf-8\"\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003c\/strong\u003eGeneric Fastener Pack (please check suitability for your specific install) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cmeta charset=\"utf-8\"\u003e\u003cstrong\u003e💡Note: \u003c\/strong\u003eOur roof mounting kits \u003cstrong\u003edo not \u003c\/strong\u003ecome with a Starlink Dish. This can be purchased from Starlink.com or a major retailer.  \u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOptional\u003c\/strong\u003e: If you require additional structural support for the stay bars, you may consider \u003ca rel=\"noopener\" title=\"Duo Cleat high wind stay bar support brackets\" href=\"https:\/\/spacetek.com.au\/products\/duo-cleat-bracket-high-wind-stay-bar-support\" target=\"_blank\"\u003eadding additional cleats\u003c\/a\u003e to the stay bar mounting points on your roof.\u003c\/p\u003e\n\u003cp data-end=\"971\" data-start=\"689\"\u003eStarlink Standard (Gen 3 \/ V4) terminals incorporate a thermal protection shut-off at approximately \u003cstrong data-end=\"782\" data-start=\"773\"\u003e50°C\u003c\/strong\u003e. The elevated pole configuration increases separation from heat-radiating metal roofing, improving airflow around the dish and reducing thermal loading during Australian summer conditions.\u003c\/p\u003e\n\u003cp data-end=\"1217\" data-start=\"973\"\u003eMultiple pole height options are available. Extended variants provide additional clearance over roof obstructions and allow space beneath the dish for secondary antennas, 4G failover equipment, point-to-point radios, or terrestrial TV hardware.\u003c\/p\u003e\n\u003ch2 data-end=\"1381\" data-start=\"1362\"\u003e\u003cstrong data-end=\"1381\" data-start=\"1365\"\u003eKey Features\u003c\/strong\u003e\u003c\/h2\u003e\n\u003cp data-end=\"1492\" data-start=\"1383\"\u003e\u003cstrong data-end=\"1411\" data-start=\"1386\"\u003e\u003cmeta charset=\"utf-8\"\u003e✅ High Wind Load Design\u003c\/strong\u003e — Reinforced mounting system suited to exposed locations and wind-prone regions.\u003c\/p\u003e\n\u003cp data-end=\"1593\" data-start=\"1494\"\u003e\u003cstrong data-end=\"1525\" data-start=\"1497\"\u003e\u003cmeta charset=\"utf-8\"\u003e✅ Gen 3 (V4) Compatibility\u003c\/strong\u003e — Precision-engineered for the Starlink Gen 3 rectangular terminal.\u003c\/p\u003e\n\u003cp data-end=\"1726\" data-start=\"1595\"\u003e\u003cstrong data-end=\"1631\" data-start=\"1598\"\u003e\u003cmeta charset=\"utf-8\"\u003e✅ Heavy Duty 40 mm Pipe Adapter\u003c\/strong\u003e — Increased wall thickness and clamping surface for improved mast retention and load handling.\u003c\/p\u003e\n\u003cp data-end=\"1874\" data-start=\"1728\"\u003e\u003cstrong data-end=\"1761\" data-start=\"1731\"\u003e\u003cmeta charset=\"utf-8\"\u003e✅ Thermal Clearance Geometry\u003c\/strong\u003e — Elevated mounting height assists airflow and reduces roof-radiated heat contributing to 50 °C shut-off events.\u003c\/p\u003e\n\u003cp data-end=\"2001\" data-start=\"1876\"\u003e\u003cstrong data-end=\"1906\" data-start=\"1879\"\u003e\u003cmeta charset=\"utf-8\"\u003e✅ Extended Height Options\u003c\/strong\u003e — Longer poles improve line-of-sight and provide space for auxiliary communications equipment.\u003cstrong data-end=\"2029\" data-start=\"2011\"\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch2 data-end=\"1964\" data-start=\"1936\"\u003e\u003cstrong data-end=\"1964\" data-start=\"1939\"\u003eInstallation Overview (also see \u003ca rel=\"noopener\" title=\"Spacetek Roof Mount Kits Installation\" href=\"https:\/\/www.youtube.com\/watch?v=0lfymRO_26k\" target=\"_blank\"\u003evideo\u003c\/a\u003e below)\u003cbr\u003e\u003cmeta charset=\"utf-8\"\u003e\u003c\/strong\u003e\u003c\/h2\u003e\n\u003col\u003e\n\u003cli\u003eIdentify a potential mounting location with clear sky visibility of the southern sky. (If in the southern hemisphere). TIP : If you are planning to mount on the nothern side of your building, ensure the height of the mount allows the Starlink to tilt and view towards the southern sky and not be obstructed by the roof's structure. \u003c\/li\u003e\n\u003cli\u003eMark fixing points for the included base plate, aligning the peaks of the roofing corrugations with the base plate.  Using pliers, lift up the fixing flaps on the base plate. (This is where the mast\/pipe will fasten onto later on).\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eApply appropriate exterior-grade sealant to all penetration points and screw in the base plate aligned to the marked fixing points. \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003ePass the Starlink Standard (Gen 3 \/ V4) cable through the pipe mast, then center the mast against the raised fixing flaps on the base plate, loosely fastening the mast to the base plate using the supplied hex bolt and nut. \u003c\/li\u003e\n\u003cli\u003eStay bars come in male \/ female pairs, loosely attach both pairs of staybars to the center mast using the pre-drilled holes. With a pair of shifters, bend up the ends of the stay bars to align to the angle of your roof's fixing points. Adjust the length of the stay bars as required to reach a secure fastening point on your roof, then fix the stay bars in place with the included tek screws. \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eConfirm mounting alignment and mechanical rigidity before continuing. \u003c\/li\u003e\n\u003cli\u003ePrepare the Starlink for final mounting position, remove the ground kickstand from the Gen 3 (V4) - consult your Starlink manual for this or see the video \u003ca rel=\"noopener\" title=\"Remove the Starlink Standard (Gen 3 \/ V4) Kickstand\" href=\"https:\/\/www.youtube.com\/shorts\/k3bLEMf6GnQ\" target=\"_blank\"\u003ehere.\u003c\/a\u003e\u003cmeta charset=\"utf-8\"\u003e \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003ePlug the Starlink Standard (Gen 3 \/ V4) cable into the back of the Starlink dish ensuring the waterproof glands fit snugly into the port. \u003c\/li\u003e\n\u003cli\u003eAssemble the two pieces of the heavy duty Spacetek pole adaptor together by following this \u003ca href=\"https:\/\/www.youtube.com\/watch?v=gwx60g_gvwY\u0026amp;t=7s\" title=\"Spacetek Heavy Duty Pipe Adapter\" rel=\"noopener\" target=\"_blank\"\u003evideo\u003c\/a\u003e. Insert the Spacetek Heavy Duty Gen 3 (V4) pole adaptor into the Starlink in the position the kickstand was occupying, ensuring it clicks into place and does not come out when agitated. It should be firmly in place. Ensure the cable is running smoothly through the adaptor. This now means the cable can run smoothly through the hole in the adapter and down into the mast. \u003c\/li\u003e\n\u003cli\u003eSlide the Spacetek pole adaptor over the end of the mounted mast, using the grub screws and allen key to tighen \/ create tension around the pole to secure the adaptor. Note - that the Starlink dish should be facing south in preparation for signal calibration, you do not need to full tighten the grub screws as yet. \u003c\/li\u003e\n\u003cli\u003eComplete the cable run \u0026amp; penetration through your roof. \u003c\/li\u003e\n\u003cli\u003eOnce the cable run is complete within the structure, plug into your router. Turn on the power and commence Starlink calibration in your Starlink App as per the instructions in Starlink documentation. \u003c\/li\u003e\n\u003cli\u003eIf required - adjust the angle of the dish by rotating the Spacetek pole adapter and adjusting the grub screws for micro-level adjustments.\u003c\/li\u003e\n\u003cli\u003eOnce fully aligned , tighten the grub screws with the included allen key. \u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch2 data-end=\"3340\" data-start=\"3090\"\u003e📽️ \u003cstrong data-end=\"3121\" data-start=\"3094\"\u003eInstallation reference:\u003c\/strong\u003e\n\u003c\/h2\u003e\n\u003cp data-end=\"3340\" data-start=\"3090\"\u003eThe tripod erection and mounting process is demonstrated in the \u003ca rel=\"noopener\" title=\"Spacetek Roof Mount installation video\" href=\"https:\/\/youtu.be\/0lfymRO_26k\" target=\"_blank\"\u003eofficial installation video\u003c\/a\u003e (Gen 2 terminal shown for method reference only). The same procedure applies to Gen 3 using the supplied heavy-duty adapter.\u003c\/p\u003e\n\u003ch2 data-end=\"3369\" data-start=\"3347\"\u003e\u003cstrong data-end=\"3369\" data-start=\"3350\"\u003eImportant Notes\u003c\/strong\u003e\u003c\/h2\u003e\n\u003cp data-end=\"3717\" data-start=\"3371\"\u003e\u003cstrong\u003e⚠️ \u003cem data-end=\"3444\" data-start=\"3374\"\u003eNot suitable for ground, freestanding, or portable installation.\u003c\/em\u003e\u003c\/strong\u003e\u003cbr data-end=\"3447\" data-start=\"3444\"\u003e\u003cstrong\u003e⚠️ \u003cem data-end=\"3514\" data-start=\"3450\"\u003eRoof penetrations must be sealed to prevent water ingress.\u003c\/em\u003e\u003c\/strong\u003e\u003cbr data-end=\"3517\" data-start=\"3514\"\u003e\u003cstrong\u003e⚠️ \u003cem data-end=\"3625\" data-start=\"3520\"\u003eThis mount is intended for high-wind regions but must still be fixed to structurally sound roofing.\u003c\/em\u003e\u003c\/strong\u003e\u003cbr data-end=\"3628\" data-start=\"3625\"\u003e\u003cstrong\u003e⚠️ \u003cem data-end=\"3717\" data-start=\"3631\"\u003eProfessional installation is strongly recommended for exposed or elevated sites.\u003c\/em\u003e\u003c\/strong\u003e\u003cstrong data-end=\"3746\" data-start=\"3727\"\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ciframe title=\"YouTube video player\" src=\"https:\/\/www.youtube.com\/embed\/gwx60g_gvwY?si=WDCTPzWxLwWtl7X4\u0026amp;start=7\" height=\"315\" width=\"560\"\u003e\u003c\/iframe\u003e\u003c\/p\u003e","brand":"TBAS","offers":[{"title":"0.6M Kit Gen 3","offer_id":47904417677547,"sku":"ST-GEN3-TINROOF-HD-0.6M","price":193.0,"currency_code":"USD","in_stock":true},{"title":"1M Kit Gen 3","offer_id":45355012751595,"sku":"ST-GEN3-TINROOF-HD-1M","price":207.0,"currency_code":"USD","in_stock":true},{"title":"1.5M Kit Gen 3","offer_id":45355012784363,"sku":"ST-GEN3-TINROOF-HD-1.5M","price":222.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0610\/5458\/3019\/files\/spacetek-heavy-duty-gen3-roof-mount-black-roof.png?v=1769833598","url":"https:\/\/spacetek.net\/products\/tin-roof-starlink-mount-roof-kit-for-dishy-gen-3-v4","provider":"SPACETEK","version":"1.0","type":"link"}